Booking today · Houston service windows 9–12 · 1–4 · 4–7 Independent Maytag specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 936-6390 Book a House Call
Error code · Range

Maytag Range Message “Feature Not Available”: Cook Cycle Entry Halted

Owners of certain Maytag ranges, among them the electric MER8650ES, may see the control scroll the message Feature Not Available across the display, sometimes paired with a note that a problem was detected. It appears when…

Medium · inspection needed
Book a House Call(713) 936-6390
Code
Feature Not Available or Fault Detected
Appliance
Range
Brand
Maytag
Warranty
30-day workmanship

What Feature Not Available or Fault Detected means

Owners of certain Maytag ranges, among them the electric MER8650ES, may see the control scroll the message Feature Not Available across the display, sometimes paired with a note that a problem was detected. It appears when the control hits a problem while you are programming a cook cycle. The display also suggests either PRESS ENTER TO TRY AGAIN or DISABLE POWER TO CLEAR. The message is a general alert rather than a specific part, so the cycle you tried to set does not start and the control waits for you to retry or reset.

Common causes of Feature Not Available or Fault Detected

  • Control that could not accept the programmed cook cycle
  • Brief power disturbance during programming
  • Oven control or its wiring if the message keeps returning
✓ One safe check you can try

1. Read the display and follow it: press Enter if it says to try again. 2. If it says to disable power, go to the breaker panel and shut off the range's breaker for sixty seconds. 3. Restore the breaker. 4. Begin a bake cycle and stay near the range for a minute. 5. If the message comes back, write down which cycle you were setting.

! Why to stop there
  • A message that repeats on different cycles points to the control or wiring, and a retry cannot separate the two.
  • We test the control and its connections before suggesting a board.
  • We give you a written price first, and our repair carries a 30-day workmanship warranty.
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Range codes

Probe or Insert ProbeMaytag Range Message "Insert Probe": Meat Probe Not Detected PUSH or PSHMaytag Range Prompt PUSH or PSH: Press Start Sabbath, Sab, 5Ab or 5A7Maytag Range Sabbath Mode Display: Cancel Sabbath Mode FEE6Maytag Range Code FEE6: Bake Element Circuit FEE7Maytag Range Code FEE7: Broil Element Concern Flashing Time, Clock, 12:00 or Power LossMaytag Range Flashing Clock or POWER LOSS: Reset the Time H on a Range CooktopMaytag Range Cooktop Showing H: Surface Still Hot Indicator Flashing on a Range CooktopMaytag Range Cooktop Indicator Light Flashing: Stuck Touch Keys
Feature Not Available or Fault DetectedFeature Not Available or Fault Detected questions
Should I press Enter or cut the power?

Do what the display says. If it offers to try again, press Enter first. If it asks you to disable power, cut power at the breaker for a minute and then restore it.

Does this message always mean a repair is needed?

No. A single occurrence after a power flicker often clears with a reset. A message that comes back on every cycle suggests the control, and that is when we should look.

Is the oven safe to use?

If the oven heats normally after the reset and no further message appears, it can be used. If it will not run a cycle, leave it off and call us.

Book a visit

Still seeing Feature Not Available or Fault Detected?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 936-6390