Booking today · Houston service windows 9–12 · 1–4 · 4–7 Independent Maytag specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 936-6390 Book a House Call
Error code · Washer

Maytag Neptune Washer Code bE: Motor Speed Signal With No Motor Running

The code bE shows up on Maytag Neptune 27-inch front-load washers, the MAH8700A and MAH9700AW families, built around 2005 and 2006. It tells you the control is receiving a motor speed (tach) signal even though the…

High · stop use, call now
Book a House Call(713) 936-6390
Code
bE
Appliance
Washer
Brand
Maytag
Warranty
30-day workmanship

What bE means

The code bE shows up on Maytag Neptune 27-inch front-load washers, the MAH8700A and MAH9700AW families, built around 2005 and 2006. It tells you the control is receiving a motor speed (tach) signal even though the motor is not running. That is a contradiction the control cannot accept, so it stops. The reading points at the speed-sensing circuit or the motor drive rather than at your clothes. These older Neptune washers remain in many homes. The display shows bE.

Common causes of bE

  • Motor speed-sensing circuit sending a signal at rest
  • Wiring or connector between the motor and the control
  • Motor control board interpreting the signal
✓ One safe check you can try

1. Stop the cycle and unplug the washer. 2. Make sure the drum is still and nothing is turning it. 3. Plug the washer back in. 4. Run a short drain and spin to see whether bE appears again. 5. If it returns, leave the washer unplugged and call us.

! Why to stop there
  • A tach signal with no motion could come from the sensor, its wiring or the control, and only testing separates them.
  • We start with the wiring because it is the least costly to correct.
  • We repair these older washers and tell you plainly when a repair is not worth it.
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Washer codes

SdMaytag Bravos Washer Code Sd: Suds Reduction Routine at the End of the Wash Sensing or Fill LightMaytag Top-Load Washer Sensing or Fill Light: Auto Sensing Is Measuring the Load SrMaytag Neptune Washer Code Sr: System Relay Problem Sud or SdMaytag Washer Code Sud or Sd: Too Many Suds, Extra Rinsing Under Way tEMaytag Neptune Washer Code tE: Sump Thermistor Reading Outside Normal Range uLMaytag Bravos Washer Code uL: Unbalanced Load, Correction Routine Running Wash Light On or FlashingMaytag Top-Load Washer Wash Light On or Flashing: Water Level Not Changing Ofb or uLMaytag Top-Load Washer Code Ofb or uL: Load Out of Balance, Hands Needed
bEbE questions
What is a tach signal?

It is the motor's speed feedback to the control. When the control sees it while the motor is idle, it assumes something is wrong in the sensing or drive circuit.

Can I run laundry if bE shows?

Not reliably. The control will stop the cycle because it cannot trust the motor reading. Wet clothes can wait while we check the speed-sensing circuit and the motor drive for you.

Is this an expensive repair?

It depends on whether we find a wiring problem or a control that needs replacing. You get a written price before we start, and you decide.

Book a visit

Still seeing bE?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 936-6390