Booking today · Houston service windows 9–12 · 1–4 · 4–7 Independent Maytag specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 936-6390 Book a House Call
Error code · Washer

Maytag Washer Code F3E2: Hoses Swapped Between Hot and Cold

On Maytag top-load HE washers with an electronic control, from the Bravos era through models such as the MVW7232HC, F3E2 can mean the hot and cold inlet hoses are installed the wrong way round: the cold…

Medium · inspection needed
Book a House Call(713) 936-6390
Code
F3E2
Appliance
Washer
Brand
Maytag
Warranty
30-day workmanship

What F3E2 means

On Maytag top-load HE washers with an electronic control, from the Bravos era through models such as the MVW7232HC, F3E2 can mean the hot and cold inlet hoses are installed the wrong way round: the cold hose is on the hot inlet and the hot hose is on the cold inlet. On Maytag front-load HE washers (MHW models such as the MHW5630HW), no cause is stated, and only a 5-minute power reset is given. The cycle stops during fill.

Common causes of F3E2

  • Hoses swapped at the washer inlets (top-loaders)
  • Faucets not fully open, or a hose not connected
  • A momentary stop that the reset clears (front-loaders)
✓ One safe check you can try

1. Check that the hot hose goes to the hot inlet and the cold hose to the cold inlet. 2. Make sure both faucets are fully open and both hoses are connected. 3. Unplug the washer for 5 minutes, then restore power. 4. Start the cycle again.

! Why to stop there
  • If the hoses are right and the code stays, the temperature sensing or inlet valves need a test
  • A faucet labeled backwards at the wall can mislead an owner, so we check what actually flows
  • No one is pushed into a repair on an older Bravos that is not worth the money
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Washer codes

uLMaytag Bravos Washer Code uL: Unbalanced Load, Correction Routine Running Wash Light On or FlashingMaytag Top-Load Washer Wash Light On or Flashing: Water Level Not Changing Ofb or uLMaytag Top-Load Washer Code Ofb or uL: Load Out of Balance, Hands Needed oLMaytag Top-Load Washer Code oL: Load Too Large for the Tub PFMaytag Washer Code PF: Cycle Interrupted by a Power Failure Rinse Light OnMaytag Top-Load Washer Rinse Light On: Spray Rinse Is Running SdMaytag Bravos Washer Code Sd: Suds Reduction Routine at the End of the Wash Sensing or Fill LightMaytag Top-Load Washer Sensing or Fill Light: Auto Sensing Is Measuring the Load
F3E2F3E2 questions
What does F3E2 mean on a Maytag top-loader?

It can indicate that the hot and cold inlet hoses are swapped. Cold water arriving at the hot inlet, or the other way round, makes the washer stop the cycle.

How do I tell which hose is which?

Match the hot faucet to the hot inlet on the washer and the cold faucet to the cold inlet. Both faucets must be fully open and both hoses connected before the washer will fill.

What if the hoses are right?

Then we test the inlet valves and the temperature sensing with the washer filling, to see where the water is actually going. We give a written price before work, and we back repairs with a 30-day warranty.

Book a visit

Still seeing F3E2?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 936-6390