Booking today · Houston service windows 9–12 · 1–4 · 4–7 Independent Maytag specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 936-6390 Book a House Call
Error code · Washer

Maytag Front-Load Washer Code F3E6: Stop Followed by a Reset Step

F3E6 is listed for Maytag front-load HE washers, the MHW models such as the MHW5630HW and MHW8630HC. The manufacturer's page states no cause for it and gives just one instruction: disconnect power for 5 minutes, then…

Medium · inspection needed
Book a House Call(713) 936-6390
Code
F3E6
Appliance
Washer
Brand
Maytag
Warranty
30-day workmanship

What F3E6 means

F3E6 is listed for Maytag front-load HE washers, the MHW models such as the MHW5630HW and MHW8630HC. The manufacturer's page states no cause for it and gives just one instruction: disconnect power for 5 minutes, then restore it. All we can say with certainty is that the control halted the cycle and put F3E6 on the display. We do not link it to a named part until the washer has been tested, and repeat appearances are what matter.

Common causes of F3E6

  • A brief stop that the power reset clears
  • A wiring or connector issue that shows up only now and then
  • The control board, only after the connections check out
✓ One safe check you can try

1. Unplug the washer. 2. Leave it off for 5 minutes. 3. Plug it in and run a short cycle. 4. If F3E6 returns, jot down when in the cycle it appeared and call us instead of resetting it again and again.

! Why to stop there
  • With no stated cause, we find the circuit by testing the washer, not by swapping parts
  • An intermittent code needs the washer to run so we can see it happen
  • With an older MHW, we compare the price of the repair to the age of the washer and tell you where it lands
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Washer codes

Ofb or uLMaytag Top-Load Washer Code Ofb or uL: Load Out of Balance, Hands Needed oLMaytag Top-Load Washer Code oL: Load Too Large for the Tub PFMaytag Washer Code PF: Cycle Interrupted by a Power Failure Rinse Light OnMaytag Top-Load Washer Rinse Light On: Spray Rinse Is Running SdMaytag Bravos Washer Code Sd: Suds Reduction Routine at the End of the Wash Sensing or Fill LightMaytag Top-Load Washer Sensing or Fill Light: Auto Sensing Is Measuring the Load SrMaytag Neptune Washer Code Sr: System Relay Problem Sud or SdMaytag Washer Code Sud or Sd: Too Many Suds, Extra Rinsing Under Way
F3E6F3E6 questions
What is F3E6 on my front-load Maytag?

The manufacturer gives no meaning for it, only a power reset. The control stopped the cycle for a reason the display does not spell out.

Can I keep resetting it?

One reset is reasonable. If the code comes back, repeated resets only hide the pattern we need to see. Tell us what the washer was doing when it appeared.

Do you repair MHW front-loaders that are several years old?

Yes. We give a written price before work, tell you plainly if a repair is not worth it, and back repairs with a 30-day warranty.

Book a visit

Still seeing F3E6?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 936-6390